Palang xích lắc tay 0.75 tấn 1.5m KUKDONG LB-90A-0.75
- Mã hàng
- KUKDONG LB-90A-0.75
Liên hệ để nhận báo giá
Phản hồi trong giờ làm việc. Cần tư vấn chọn đúng tiêu chuẩn? Ghi rõ môi trường sử dụng trong yêu cầu.
Thông số kỹ thuật
Lấy từ tài liệu nhà sản xuất. Mỗi thông số ghi rõ nguồn đã đối chiếu.
- A (mm)
- 145 Nguồn: Website
- B (mm)
- 86 Nguồn: Website
- D (mm)
- 122 Nguồn: Website
- G (mm)
- 30 Nguồn: Website
- L (mm)
- 320 Nguồn: Website
- 8. Roller
- 18. Ratchet Disk Nguồn: Website
- 10. Stripper
- 20. Break Cover Assembly Nguồn: Website
- 3. Drive Shaft
- 13. Pawl Nguồn: Website
- 6. Load Sheave
- 16. Free Spring Nguồn: Website
- 7. Guide Plate
- 17. Friction Disk Nguồn: Website
- 4. Splined Gear
- 14. Snap Ring Nguồn: Website
- 9. Bearing Race
- 19. Femail Thread Grip Nguồn: Website
- Thương hiệu
- KUKDONG Nguồn: Website
- Mã sản phẩm
- LB-90A-0.75 Nguồn: Website
- 1. Gear Case Assembly
- 11. Lever side plate Assembly Nguồn: Website
- 2. Disk Gear Assembly
- 12. Pawl Spring Nguồn: Website
- Chiều cao nâng (m) (*)
- 1.5 Nguồn: Website
- 5. Gear Side Plate Assembly
- 15. Disk Hub Nguồn: Website
- Khối lượng tịnh (Kg)
- 7.2 Nguồn: Website
- Lực tay tác động (Kg)
- 14 Nguồn: Website
- Tải trọng nâng (Tấn)
- 0.75 Nguồn: Website
- Khả năng thử tải (Kg)
- 940 Nguồn: Website
- Xích tải (mm) x số sợi
- Ø 6.0 x 1 Nguồn: Website
- 1. DO NOT APPLY OVER SPECIFIED LOAD.
- 2. DO NOT USE DEFORMED PARTS. Nguồn: Website
- 5. DO NOT USE TWISTED OR KINKED CHAIN.
- 6. DO NOT USE TO THE MAX. AND MIN. Nguồn: Website
- 7. DO USE IT AFTER LOCK LEVER′S WORK.
- 8. DO NOT TRY TO SUSPEND A LOADING WITH TWO BLOCKS. Nguồn: Website
- 3.DO USE IT IN THE STRAIGHT WAY BETWEEN CHAIN AND TOP, BOTTOM HOOK.
- 4. DO NOT GIVE IMPACT LOAD TO TOP & BOTTOM HOOK AND CHAIN. Nguồn: Website
Mô tả
CHOOSE CORRECT CAPACITY AFTER CONSIDERING LOADING WEIGHT.
APPLY OIL TO LOAD CHAIN ANF CHECK IF LOAD CHAIN IS TWISTED OR NOT.
USE LOAD CHAIN IN A STRAIGHT WAY.
HOW TO ADJUST THE LENGTH OF LOAD CHAIN
APPLY OIL TO JOINT PARTS OF LOAD CHAIN, HOOK & LOCK LEVER AFTER REMOVING DUST & MOISTURE.
KEEP THEM WHERE IS WELL VENTILATED OR DRIED.
REMOVE LOAD CHAIN : REMOVE ′END RING′ AND THEN REMOVE IT IN THE RELEASED STATUS.
DISASSEMBLE LEVER, BRAKE : DISASSEMBLE THEM FROM LEFT TO RIGHT OF PART LIST.
DISASSEMBLE GEAR, CENTER PART : DISASSEMBLE THEM FROM RIGHT TO LEFT OF PART LIST.
[ASS′Y] OPPOSITE OF DISASS′Y
[DISASS′Y 1] DEFORMITY OF END RING, CHAIN, BOTTOM HOOK.
[DISASS′Y 2] DEFORMITY OF LEVER, GRIP RING, STOPPER, BRAKE DISK, RATCHET GEAR, HUB, PAWL.
[DISASS′Y 3] DEFORMITY OF GEAR COVER, GEAR SIDE PLATE, TOP HOOK, TOP HOOK BOLT, GUIDE, LOAD SHEAVE, STRIPPER.
OIL MUST BE APPLIED ON CONTACT SURFACE OF BRAKE DISK.
HOW TO ADJUST ′BRAKE′ PUT ′CHANGE LEVER′ ON ′UP′ PULL LOAD CHAIN OF HOOK. BRAKE WORKS. RELEASE CASTLE NUT′S GROOVE A BIT AT CASTLE NUT′S COMPLETE FASTENING [PIC.1) A] AND THEN, INSERT SPLIT PIN [PIC.1) B] AND COMBINE REVOLVING AS PIC.2)
PUT ′CHANGE LEVER′ ON ′UP′
PULL LOAD CHAIN OF HOOK.
RELEASE CASTLE NUT′S GROOVE A BIT AT CASTLE NUT′S COMPLETE FASTENING [PIC.1) A] AND THEN, INSERT SPLIT PIN [PIC.1) B] AND COMBINE REVOLVING AS PIC.2)
[PIC.1) A] AND THEN, INSERT SPLIT PIN
[PIC.1) B] AND COMBINE REVOLVING AS PIC.2)
AUTOMATIC BRAKE OPERATION WITHOUT GRIP RING′S WORK. (POSSIBLE TO ADJUST CHAIN′S LENGTH PULLING CHAIN)
IN CASE YOU PULL CHAIN STRONGLY, BRAKE WORKS. SO USE LIGHT POWER.
BRAKE WORK AUTOMATICALLY. BUT IN CASE OF LOAD OF BELOW 35kgf, BRAKE IS NOT WORKING.